We'll take a good look at disk-oriented aspects of Gentoo Linux and Linux in general, including Linux filesystems, partitions and block devices. Then, once you're familiar with the ins and outs of disks and filesystems, you'll be guided through the process of setting up partitions and filesystems for your Gentoo Linux installation.

To begin, we'll introduce block devices. The most famous block device is probably the one that represents the first SCSI HD in a Linux system, namely /dev/sda.

The block devices above represent an abstract interface to the disk. User programs can use these block devices to interact with your disk without worrying about whether your drives are IDE, SCSI or something else. The program can simply address the storage on the disk as a bunch of contiguous, randomly-accessible 512-byte blocks.

Although it is theoretically possible to use a full disk to house your Linux system, this is almost never done in practice. Instead, full disk block devices are split up in smaller, more manageable block devices. On most systems, these are called partitions. Other architectures use a similar technique, called slices.

The number of partitions is highly dependent on your environment. For instance, if you have lots of users, you will most likely want to have your /home separate as it increases security and makes backups easier. If you are installing Gentoo to perform as a mailserver, your /var should be separate as all mails are stored inside /var. A good choice of filesystem will then maximise your performance. Gameservers will have a separate /opt as most gaming servers are installed there. The reason is similar for /home: security and backups.

As you can see, it very much depends on what you want to achieve. Separate partitions or volumes have the following advantages:

• You can choose the best performing filesystem for each partition or volume
• Your entire system cannot run out of free space if one defunct tool is continuously writing files to a partition or volume
• If necessary, file system checks are reduced in time, as multiple checks can be done in parallel (although this advantage is more with multiple disks than it is with multiple partitions)
• Security can be enhanced by mounting some partitions or volumes read-only, nosuid (setuid bits are ignored), noexec (executable bits are ignored) etc.

However, multiple partitions have one big disadvantage: if not configured properly, you might result in having a system with lots of free space on one partition and none on another.

Now that your partitions are created, it is time to place a filesystem on them. If you don't care about what filesystem to choose and are happy with what we use as default in this handbook, continue with Applying a Filesystem to a Partition. Otherwise read on to learn about the available filesystems...

Several filesystems are available. Ext2, ext3 and reiserfs are found stable on the HPPA architecture. The others are very experimental.

ext2 is the tried and true Linux filesystem but doesn't have metadata journaling, which means that routine ext2 filesystem checks at startup time can be quite time-consuming. There is now quite a selection of newer-generation journaled filesystems that can be checked for consistency very quickly and are thus generally preferred over their non-journaled counterparts. Journaled filesystems prevent long delays when you boot your system and your filesystem happens to be in an inconsistent state.

ext3 is the journaled version of the ext2 filesystem, providing metadata journaling for fast recovery in addition to other enhanced journaling modes like full data and ordered data journaling. ext3 is a very good and reliable filesystem. It has an additional hashed b-tree indexing option that enables high performance in almost all situations. In short, ext3 is an excellent filesystem.

ReiserFS is a B*-tree based filesystem that has very good overall performance and greatly outperforms both ext2 and ext3 when dealing with small files (files less than 4k), often by a factor of 10x-15x. ReiserFS also scales extremely well and has metadata journaling. As of kernel 2.4.18+, ReiserFS is solid and usable as both general-purpose filesystem and for extreme cases such as the creation of large filesystems, the use of many small files, very large files and directories containing tens of thousands of files.

XFS is a filesystem with metadata journaling that is fully supported under Gentoo Linux's xfs-sources kernel. It comes with a robust feature-set and is optimized for scalability. We only recommend using this filesystem on Linux systems with high-end SCSI and/or fibre channel storage and a uninterruptible power supply. Because XFS aggressively caches in-transit data in RAM, improperly designed programs (those that don't take proper precautions when writing files to disk and there are quite a few of them) can lose a good deal of data if the system goes down unexpectedly.

JFS is IBM's high-performance journaling filesystem. It has recently become production-ready and there hasn't been a sufficient track record to comment positively nor negatively on its general stability at this point.

To create a filesystem on a partition or volume, there are tools available for each possible filesystem:

For instance, to have the boot partition (/dev/sda2 in our example) in ext2 and the root partition (/dev/sda4 in our example) in ext3 (as in our example), you would use:

# mke2fs /dev/sda2
# mke2fs -j /dev/sda4

Now create the filesystems on your newly created partitions (or logical volumes).

mkswap is the command that is used to initialize swap partitions:

# mkswap /dev/sda3

To activate the swap partition, use swapon:

# swapon /dev/sda3

Create and activate the swap now.