We'll take a good look at some of the disk-oriented aspects of Gentoo Linux and Linux in general, including Linux filesystems, partitions, and block devices. Then, once you're familiar with the ins and outs of disks and filesystems, you'll be guided through the process of setting up partitions and filesystems for your Gentoo Linux installation.

To begin, we introduce block devices. The most typical block device is probably the one that represents the first SCSI hard disk in a Linux system, namely /dev/sda.

Block devices represent an abstract interface to the disk. User programs can use these block devices to interact with your disk without worrying about whether your drives are IDE, SCSI, or something else. The program can simply address the storage on the disk as a bunch of contiguous, randomly-accessible 512-byte blocks.

Block devices show up as entries in /dev/. Typically, the first SCSI drive is named /dev/sda, the second /dev/sdb, and so on. IDE drives are named similarly, however, they are prefixed by hd- instead of sd-. If you are using IDE drives, the first one will be named /dev/hda, the second /dev/hdb, and so on.

Although it is theoretically possible to use the entire disk to house your Linux system, this is almost never done in practice. Instead, full disk block devices are split up in smaller, more manageable block devices. These are known as partitions or slices.

The first partition on the first SCSI disk is /dev/sda1, the second /dev/sda2 and so on. Similarly, the first two partitions on the first IDE disk are /dev/hda1 and /dev/hda2.

The third partition on Sun systems is set aside as a special "whole disk" slice. This partition must not contain a file system.

Users who are used to the DOS partitioning scheme should note that Sun disklabels do not have "primary" and "extended" partitions. Instead, up to eight partitions are available per drive, with the third of these being reserved.

If you are not interested in drawing up a partitioning scheme, the table below suggests a suitable starting point for most systems. For IDE-based systems, substitute hda for sda in the following.

Note that a separate /boot partition is generally not recommended on SPARC, as it complicates the bootloader configuration.

The following parts explain how to create the example partition layout described previously, namely:

Change the partition layout as required. Remember to keep the root partition entirely within the first 2 GBytes of the disk for older systems. There is also a 15-partition limit for SCSI and SATA.

Start fdisk with your disk as argument:

# fdisk /dev/sda

You should be greeted with the fdisk prompt:

Command (m for help):

To view the available partitions, type in p:

Command (m for help): p

Disk /dev/sda (Sun disk label): 64 heads, 32 sectors, 8635 cylinders
Units = cylinders of 2048 * 512 bytes

   Device Flag    Start       End    Blocks   Id  System
/dev/sda1             0       488    499712   83  Linux native
/dev/sda2           488       976    499712   82  Linux swap
/dev/sda3             0      8635   8842240    5  Whole disk
/dev/sda4           976      1953   1000448   83  Linux native
/dev/sda5          1953      2144    195584   83  Linux native
/dev/sda6          2144      8635   6646784   83  Linux native

Note the Sun disk label in the output. If this is missing, the disk is using the DOS-partitioning, not the Sun partitioning. In this case, use s to ensure that the disk has a sun partition table:

Command (m for help): s
Building a new sun disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.

Drive type
   ?   auto configure
   0   custom (with hardware detected defaults)
   a   Quantum ProDrive 80S
   b   Quantum ProDrive 105S
   c   CDC Wren IV 94171-344
   d   IBM DPES-31080
   e   IBM DORS-32160
   f   IBM DNES-318350
   g   SEAGATE ST34371
   h   SUN0104
   i   SUN0207
   j   SUN0327
   k   SUN0340
   l   SUN0424
   m   SUN0535
   n   SUN0669
   o   SUN1.0G
   p   SUN1.05
   q   SUN1.3G
   r   SUN2.1G
   s   IOMEGA Jaz
Select type (? for auto, 0 for custom): 0
Heads (1-1024, default 64): 
Using default value 64
Sectors/track (1-1024, default 32): 
Using default value 32
Cylinders (1-65535, default 8635): 
Using default value 8635
Alternate cylinders (0-65535, default 2): 
Using default value 2
Physical cylinders (0-65535, default 8637): 
Using default value 8637
Rotation speed (rpm) (1-100000, default 5400): 10000
Interleave factor (1-32, default 1): 
Using default value 1
Extra sectors per cylinder (0-32, default 0): 
Using default value 0

You can find the correct values in your disk's documentation. The 'auto configure' option does not usually work.

It's time to delete any existing partitions. To do this, type d and hit Enter. You will then be prompted for the partition number you would like to delete. To delete a pre-existing /dev/sda1, you would type:

Command (m for help): d
Partition number (1-4): 1

You should not delete partition 3 (whole disk). This is required. If this partition does not exist, follow the "Creating a Sun Disklabel" instructions above.

After deleting all partitions except the Whole disk slice, you should have a partition layout similar to the following:

Command (m for help): p

Disk /dev/sda (Sun disk label): 64 heads, 32 sectors, 8635 cylinders
Units = cylinders of 2048 * 512 bytes

   Device Flag    Start       End    Blocks   Id  System
/dev/sda3             0      8635   8842240    5  Whole disk

We're ready to create the root partition. To do this, type n to create a new partition, then type 1 to create the partition. When prompted for the first cylinder, hit enter. When prompted for the last cylinder, type +512M to create a partition 512MBytes in size. Make sure that the entire root partition fits within the first 2GBytes of the disk. You can see output from these steps below:

Command (m for help): n
Partition number (1-8): 1
First cylinder (0-8635): (press Enter)
Last cylinder or +size or +sizeM or +sizeK (0-8635, default 8635): +512M

Now, when you type p, you should see the following partition printout:

Command (m for help): p

Disk /dev/sda (Sun disk label): 64 heads, 32 sectors, 8635 cylinders
Units = cylinders of 2048 * 512 bytes

   Device Flag    Start       End    Blocks   Id  System
/dev/sda1             0       488    499712   83  Linux native
/dev/sda3             0      8635   8842240    5  Whole disk

Next, let's create the swap partition. To do this, type n to create a new partition, then 2 to create the second partition, /dev/sda2 in our case. When prompted for the first cylinder, hit enter. When prompted for the last cylinder, type +512M to create a partition 512MB in size. After you've done this, type t to set the partition type, and then type in 82 to set the partition type to "Linux Swap". After completing these steps, typing p should display a partition table that looks similar to this:

Command (m for help): p

Disk /dev/sda (Sun disk label): 64 heads, 32 sectors, 8635 cylinders
Units = cylinders of 2048 * 512 bytes

   Device Flag    Start       End    Blocks   Id  System
/dev/sda1             0       488    499712   83  Linux native
/dev/sda2           488       976    499712   82  Linux swap
/dev/sda3             0      8635   8842240    5  Whole disk

Finally, let's create the /usr, /var and /home partitions. As before, type n to create a new partition, then type 4 to create the third partition, /dev/sda4 in our case. When prompted for the first cylinder, hit enter. When prompted for the last cylinder, enter +2048M to create a partition 2 GBytes in size. Repeat this process for sda5 and sda6, using the desired sizes. Once you're done, you should see something like this:

Command (m for help): p

Disk /dev/sda (Sun disk label): 64 heads, 32 sectors, 8635 cylinders
Units = cylinders of 2048 * 512 bytes

   Device Flag    Start       End    Blocks   Id  System
/dev/sda1             0       488    499712   83  Linux native
/dev/sda2           488       976    499712   82  Linux swap
/dev/sda3             0      8635   8842240    5  Whole disk
/dev/sda4           976      1953   1000448   83  Linux native
/dev/sda5          1953      2144    195584   83  Linux native
/dev/sda6          2144      8635   6646784   83  Linux native

To save your partition layout and exit fdisk, type w:

Command (m for help): w

Now that your partitions are created, you can now continue with Creating Filesystems.

Now that your partitions are created, it is time to place a filesystem on them. If you don't care about what filesystem to choose and are happy with what is used as default in this handbook, continue with Applying a Filesystem to a Partition. Otherwise, read on to learn about the available filesystems...

Several filesystems are available, some are known to be stable on the SPARC architecture. Ext2 and ext3, for example, are known to work well. Alternate filesystems may not function correctly.

ext2 is the tried-and-true Linux filesystem. It does not support journaling, which means that periodic checks of ext2 filesystems at startup can be quite time-consuming. There is quite a selection of newer-generation journaled filesystems that can be checked for consistency very quickly at startup, and are therefore generally preferred over their non-journaled counterparts. In general, journaled filesystems prevent long delays when a system is booted and the filesystem is in an inconsistent state.

ext3 is the journaled version of the ext2 filesystem. It provides metadata journaling for fast recovery as well as other enhanced journaling modes like full-data and ordered-data journaling. Ext3 makes an excellent and reliable alternative to ext2.

To create a filesystem on a partition or volume, tools specific to the chosen filesystem are available:

For instance, to create the root partition (/dev/sda1 in our example) as ext2, and the /usr, /var, and /home partitions (/dev/sda4, 5 and 6 in our example, respectively) as ext3, you would use:

# mke2fs /dev/sda1
# mke2fs -j /dev/sda4
# mke2fs -j /dev/sda5
# mke2fs -j /dev/sda6

mkswap is the command used to initialize swap partitions:

# mkswap /dev/sda2

To activate the swap partition, use swapon:

# swapon /dev/sda2

Create and activate the swap with the commands mentioned above.