doc/en/migration-to-2.6.xml

<?xml version='1.0' encoding="UTF-8"?>
<!DOCTYPE guide SYSTEM "/dtd/guide.dtd">

<!-- $Header: /var/cvsroot/gentoo/xml/htdocs/doc/en/migration-to-2.6.xml,v 1.14 2005/04/02 10:17:36 swift Exp $ -->

<guide link="/doc/en/migration-to-2.6.xml">

<title>The complete Gentoo Linux 2.6 migration guide</title>

<author title="Author">
        <mail link="dsd@gentoo.org">Daniel Drake</mail>
</author>
<author title="Contributor">
        <mail link="sergey_zlodey@mail.ru">Sergey Galkin</mail>
</author>
<author title="Contributor">
        <mail link="svyatogor@gentoo.org">Sergey Kuleshov</mail>
</author>
<author title="Editor">
        <mail link="neysx@gentoo.org">Xavier Neys</mail>
</author>
<author title="Editor">
        <mail link="bennyc@gentoo.org">Benny Chuang</mail>
</author>

<abstract>
This document will aid you in the process of migrating from Linux 2.4 to Linux
2.6, devfs to udev, OSS to ALSA, and LVM to LVM2.
</abstract>

<version>0.2.6</version>
<date>2005-04-07</date>

<chapter>
<title>Introduction</title>

<section>
<title>Whats new in Linux 2.6?</title>
<body>

<p>
That is no easy question to answer. Linux 2.6 is the result of over 2 years
of rapid development and stabilisation of new features, and is architectually
quite different from its 2.4 counterpart. Some of the more major changes are
listed below:
</p>

<ul>
  <li>
    Scheduler/Interactivity improvements: Linux feels very smooth on desktop
    systems and copes much better than 2.4 while under load
</li>
  <li>
    Scalability: Linux now scales much better at both ends - on small embedded
    devices and also systems with many processors
  </li>
  <li>Performance: Throughput from common applications is much improved</li>
  <li>
    Hardware support: Linux now supports many more architectures and hardware
    devices out-of-the-box than any other operating system.
</li>
</ul>

<p>
Joseph Pranevich has written a very detailed document, <uri
link="http://www.kniggit.net/wwol26.html">The Wonderful World Of Linux
2.6</uri> which you may be interested to glance over. If you are interested in
the more technical details, you can refer to <uri
link="http://www.linux.org.uk/~davej/docs/post-halloween-2.6.txt">The
post-halloween document</uri> - but bear in mind that this is somewhat outdated
now.
</p>

</body>
</section>
<section>
<title>What is udev?</title>
<body>

<p>
In the past, Gentoo has instructed users to use <e>devfs</e> for managing the
/dev directory, which contains a series of device interfaces to allow system
applications to communicate with hardware (through the kernel).
</p>

<p>
<e>devfs</e>, whilst a good concept, has some internal problems, and has been
marked obselete in Linux 2.6.
</p>

<p>
<e>udev</e> is the new way of managing device nodes. It addresses issues with
previous device managers, and also attempts to solve some other problems.
</p>

<p>
The above may not mean much to you, but fear not, the hard working Gentoo
developers have put effort into making the migration from devfs very easy.
</p>

</body>
</section>
<section>
<title>What is ALSA?</title>
<body>

<p>
With Linux 2.4, chances are that you used OSS (open sound system) drivers to
power your sound card. OSS has been replaced by a newer and better set of sound
drivers: ALSA.
</p>

<p>
ALSA, the Advanced Linux Sound Architecture, is a new set of sound drivers with
a new and improved API, present in the Linux 2.6 kernel. It is backwards
compatible with OSS applications, provided that you select the right kernel
configuration options!
</p>

<note>
If you do not have any sound/audio hardware, you can safely skip over any
ALSA-related instructions in this document.
</note>

</body>
</section>
<section>
<title>What is LVM?</title>
<body>

<p>
<e>Logical Volume Management</e> (LVM) exists as set of tools allowing you to
manage your disk storage in a very flexible manner. Amongst other things, it
allows powerful control over partitions (e.g. resizing without reboot), and
makes operations like device changes relatively simple. LVM acts as an
alternative to standard partition-based disk management.
</p>

<p>
LVM support has historically been implemented in Linux 2.4. Linux 2.6 features
a new version of LVM, named <e>LVM2</e>. The migration process requires you to
install new versions of the user-level tools (covered later in this document)
but will leave your data intact!
</p>

<p>
<e>If you do not currently use LVM for data-storage management, then LVM2
migration does not apply to you.</e> If this is the case, you can safely ignore
any parts of this document referencing LVM/LVM2. Upgrading to Linux 2.6 does
<e>not</e> require you to store your data on LVM partitions - you can keep
your data in the standard partition-format as it always has been.
</p>

<p>
If you are not a LVM user, but you think LVM2 sounds useful for you, you can
convert your disks to this format at a later date, by following the
<uri link="http://www.gentoo.org/doc/en/lvm2.xml">Gentoo LVM2 Installation
Guide</uri>. For now, lets just concentrate on getting a smooth 2.6 migration
underway.
</p>

</body>
</section>
</chapter>

<chapter>
<title>Preparation</title>
<section>
<title>Get your system up-to-date</title>
<body>

<p>
Some of the changes brought in with Linux 2.6 also required some changes in the
base system applications. Before continuing, you should ensure that your system
is relatively up-to-date, and to be perfectly sure, you should update all world
and system packages where updates are available.
</p>

<p>
In particular, make sure you have the latest stable versions of the following
packages:
</p>

<ul>
  <li><c>sys-apps/baselayout</c></li>
  <li><c>sys-apps/util-linux</c></li>
  <li>
    <c>sys-kernel/genkernel</c> (only if you wish to use genkernel as opposed
    to manual configuration)
</li>
</ul>

<pre caption="Updating all world packages">
# <i>emerge --sync</i>
# <i>emerge -ua world</i>
</pre>

</body>
</section>
<section>
<title>modutils vs module-init-tools</title>
<body>

<p>
<c>sys-apps/modutils</c> is the package that provides tools such as
<c>modprobe</c>, <c>rmmod</c> and <c>insmod</c> for Linux 2.4.
</p>

<p>
Linux 2.6 introduces a new module format, and therefore requires new tools for
handling modules. These are bundled up into the
<c>sys-apps/module-init-tools</c> package.  </p>

<p>
You should now remove modutils and install module-init-tools:
</p>

<pre caption="Switching from modutils to module-init-tools">
# <i>emerge --unmerge sys-apps/modutils</i>
# <i>emerge module-init-tools</i>
</pre>

<note>
Don't worry - even though you have just unmerged modutils, module-init-tools
provides backwards compatibility for Linux 2.4, so you will still be
able to boot into Linux 2.4 and handle modules for that kernel.
</note>

<note>
For the above reason, module-init-tools might already be installed and working
with your existing Linux 2.4 kernel. In this case, you don't need to worry
about this stage - your system is already ready to deal with Linux 2.6 modules.
</note>

</body>
</section>
<section>
<title>Installing udev</title>
<body>

<p>
There is no configuration involved here. Simply use <c>emerge</c> to install
udev:
</p>

<pre caption="Installing udev">
# <i>emerge -a udev</i>
</pre>

<p>
You should now read the 
<uri link="http://www.gentoo.org/doc/en/udev-guide.xml">Gentoo udev
Guide</uri> to get a more complete idea about the differences between udev
and devfs.
</p>

</body>
</section>
<section>
<title>Checking for essential device nodes</title>
<body>

<p>
When the system boots up, the system requires some essential device nodes. As
udev is not included in the kernel, it is not activated immediately. To work
around this, you must ensure that you have some essential device nodes on your
disk.
</p>

<p>
Our installation stage files will have created the required devices during the
initial installation. However, some users have reported that this is not the
case. We will use this opportunity to check that the device files exist, and
create them if they do not.
</p>

<p>
As your existing device manager will be mounted at /dev, we cannot access it
directly. So we will bind-mount your root partition to another location and
access the /dev directory from there.
</p>

<pre caption="Bind-mounting your root partition and listing static devices">
# <i>mkdir -p /mnt/temp</i>
# <i>mount -o bind / /mnt/temp</i>
# <i>cd /mnt/temp/dev</i>
# <i>ls -l console null</i>
</pre>

<p>
If the above <e>ls</e> command reported that either <c>console</c> or
<c>null</c> do not exist, then you must create them yourself, as shown below.
</p>

<pre caption="Creating the missing console and null nodes">
# <i>mknod -m 660 console c 5 1</i>
# <i>mknod -m 660 null c 1 3</i>
</pre>

<p>
You should now unmount your bind-mounted root partition, even if you did not
have to create those devices:
</p>

<pre caption="Unmounting the bind-mounted root">
# <i>cd</i>
# <i>umount /mnt/temp</i>
# <i>rmdir /mnt/temp</i>
</pre>

</body>
</section>
<section>
<title>Installing ALSA utilities</title>
<body>

<p>
ALSA requires you to have some packages installed, so that applications can use
the ALSA API. These packages will also allow you to control the mixer and
volume levels. Install the required utilities as follows:
</p>

<pre caption="Installing ALSA utilities and libraries">
# <i>emerge -a alsa-lib alsa-utils alsa-tools alsa-headers alsa-oss</i>
</pre>

</body>
</section>
</chapter>

<chapter>
<title>Installing the Linux 2.6 sources</title>

<section>
<title>Choosing and installing a kernel</title>
<body>

<p>
The first thing you need to do is install sources of a 2.6 kernel of your
choice. The two Gentoo-supported 2.6 kernels are currently
<e>gentoo-sources</e> (for desktops) and <e>hardened-dev-sources</e> (for
servers). There are others available, see the <uri
link="/doc/en/gentoo-kernel.xml">Gentoo Linux Kernel Guide</uri> for more
choices.
</p>

<p>
In this guide, we'll use <c>gentoo-sources</c> as an example. Install your
chosen set of kernel sources using the <c>emerge</c> utility:
</p>

<pre caption="Installing gentoo-sources">
# <i>emerge -a gentoo-sources</i>
These are the packages that I would merge, in order:
Calculating dependencies ...done!
[ebuild  NS   ] sys-kernel/gentoo-sources-2.6.10-r4

Do you want me to merge these packages? [Yes/No] <i>y</i>
</pre>

<p>
When performing the above <c>emerge</c> command, if you find that it wants to
install a 2.4 version of gentoo-sources (e.g. <c>gentoo-sources-2.4.26</c>),
then it means that the profile you are using is not designed for Linux 2.6
users. Please follow the
<uri link="/doc/en/gentoo-upgrading.xml">Gentoo Upgrading Document</uri> to 
switch to a 2.6-based profile, and retry installing 2.6 kernel sources.
</p>

</body>
</section>
<section>
<title>Updating the /usr/src/linux symbolic link</title>
<body>

<p>
Various components of the Gentoo utilities rely on /usr/src/linux being a
symbolic link to the kernel sources that you are running (or wish to compile
against).
</p>

<p>
We will now update our /usr/src/linux link to point at the kernel sources we
just installed. Continuing our example:
</p>

<pre caption="Updating the /usr/src/linux softlink">
# <i>cd /usr/src</i>
# <i>ln -sfn linux-2.6.10-gentoo-r4 linux</i>
</pre>

</body>
</section>
</chapter>

<chapter id="pitfalls">
<title>Known pitfalls with Linux 2.6 migration</title>
<section>
<body>

<p>
Before we get stuck into configuring the kernel, I'll attempt to detail the
most common errors that people make when migrating to Linux 2.6, as some of
these points will influence the way you configure the new kernel.
</p>

<note>
Not all of these points are relevant at this stage, but I will detail them all
here in one place, and you can refer back at your leisure.
</note>

</body>
</section>
<section>
<title>Don't use "make oldconfig" with a 2.4 .config</title>
<body>

<note>
If you don't understand what this means, don't worry, you won't make this
mistake if you follow the rest of this guide correctly.
</note>

<p>
You'll be asked many many questions, since there have been a large amount of
changes. Many people who do try a <c>make oldconfig</c> from a 2.4 config end
up creating an unworkable kernel (e.g. no output on-screen, no input from
keyboard, etc). Please save yourself the trouble, and use the traditional
<c>menuconfig</c> configuration method just this once.
</p>

</body>
</section>
<section>
<title>Don't use ide-scsi for CD/DVD writing</title>
<body>

<p>
In Linux 2.4, the only way to achieve good CD/DVD writing results was to enable
the (rather ugly) <c>ide-scsi</c> emulation. Thankfully, the IDE layer in Linux
2.6 has been extended to support CD/DVD writers much better.
</p>

<p>
You don't need to enable any extra options to support CD writing. Just be sure
<e>not</e> to enable <c>ide-scsi</c> as you used to.
</p>

</body>
</section>
<section>
<title>PC Speaker is now a configurable option</title>
<body>

<p>
You won't get your normal console beeps (or any response from the PC speaker at
all) unless you specifically enable the new PC speaker option
(<c>CONFIG_INPUT_PCSPKR</c>):
</p>

<pre caption="Location of PC speaker option">
Device Drivers  ---&gt;
 Input device support  ---&gt;
  [*] Misc
   &lt;*&gt;   PC Speaker support
</pre>

<note>
By "PC speaker", I am referring to the analogue speaker that beeps once when
your system is powering up, I am not referring to normal sound hardware used
for playing music, etc.
</note>

</body>
</section>
<section>
<title>New USB Storage block device driver sometimes problematic</title>
<body>

<p>
Very recently, a new USB storage device driver has been added to the kernel.
At the time of writing, this driver ("ub") is still in its early stages and
some users find it to be unreliable. If you have problems accessing your USB
hard disk, USB flash disk, USB card reader, or USB digital camera, then you
could try reverting to the older SCSI-style driver:
</p>

<pre caption="Disabling ub">
Device Drivers  ---&gt;
 Block devices  ---&gt;
  &lt; &gt; Low Performance USB Block driver
</pre>

<note>
The older SCSI-style driver (USB Mass Storage support) is enabled by default.
It can be found under "Device Drivers --&gt; USB support", but will generally
not come into effect while ub is also present.
</note>

</body>
</section>
<section>
<title>usbdevfs renamed to usbfs</title>
<body>

<p>
If you have edited your <path>/etc/fstab</path> file to customise the way that
the USB device filesystem gets mounted, you may have to modify the filesystem
type from <e>usbdevfs</e> to <e>usbfs</e>.
</p>

<note>
Recent 2.4 kernels will also allow you to use "usbfs" as well as "usbdevfs", so
you aren't breaking any backwards compatibility by doing this.
</note>

</body>
</section>
<section>
<title>Don't renice X</title>
<body>

<p>
If you are a desktop 2.4 user, you may have hacked your system into running X
at a higher priority, as in some cases it seems to provide better desktop
performance.
</p>

<p>
There have been many scheduler changes in 2.6 which change this behaviour. If
you continue to run X at a higher priority, it will do exactly what it is
supposed to (run the <e>display server</e> at a very high priority) and you
will notice consequences such as sound stuttering and slow application load
times because your CPU is spending too long serving X and only X.
</p>

<p>
In Linux 2.6, you no longer need to renice desktop applications to get good
interactivity. Please remove your "niceness" hacks!
</p>

</body>
</section>
<section>
<title>X11 config file should now use /dev/input/mice for PS/2 and USB
mice</title>
<body>

<p>
One of the changes that a default udev configuration introduces is different
organisation of the mouse device nodes. Previously, you would have had nodes
such as <path>/dev/psaux</path> and <path>/dev/mouse</path>. You will now have
nodes such as <path>/dev/input/mouse0</path>, <path>/dev/input/mouse1</path>,
and a collective <path>/dev/input/mice</path> node which combines movements
from all mice.
</p>

<p>
Since the old X configurations typically reference <path>/dev/mouse</path> or
<path>/dev/psaux</path> then you may get an error similar to the one shown
below when you attempt to start X11:
</p>

<pre caption="Common error when starting X on a udev system for the first time">
(EE) xf86OpenSerial: Cannot open device /dev/mouse
        No such file or directory.
(EE) Mouse0: cannot open input device
(EE) PreInit failed for input device "Mouse0"
No core pointer
</pre>

<p>
To correct this, open your X11 config in a text editor, and update the mouse
<e>InputDevice</e> section to use the <path>/dev/input/mice</path> device. An
example is shown below:
</p>

<pre caption="Opening your X11 config file">
# <i>nano -w /etc/X11/xorg.conf</i>
</pre>

<note>
If you are still using XFree86, your config file will be
<path>/etc/X11/XF86Config</path>
</note>

<pre caption="Sample mouse InputDevice section">
Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "auto"
        Option      "Device" "/dev/input/mice"
EndSection
</pre>

<note>
If you are using a serial mouse, the new device path will be
<path>/dev/tts/0</path> instead of <path>/dev/ttyS0</path>.
</note>

</body>
</section>
<section>
<title>New Serial-ATA (SATA) drivers name the devices differently</title>
<body>

<p>
If you used the original Serial ATA drivers under Linux 2.4, you probably
observed your SATA devices having names such as <c>/dev/hde</c>.
</p>

<p>
Linux 2.6 introduces some new SATA drivers (libata) which are based on the
SCSI subsystem. As these drivers are based on SCSI, your SATA disks will now
show up as SCSI devices. Your first SATA disk will be named <c>/dev/sda</c>.
You will need to update your <c>/etc/fstab</c> file to reflect this, and you
will need to bear this in mind when choosing the root/real_root kernel boot
parameter later on.
</p>

<note>
libata has been backported into recent versions of Linux 2.4, so you may
already be familiar with the new device naming.
</note>

</body>
</section>
<section>
<title>bootsplash no longer maintained</title>
<body>

<p>
If you used the <c>gentoo-sources-2.4</c> kernel, you may have used the
<e>bootsplash</e> functionality in order to provide yourself with a colourful
framebuffer console.
</p>

<p>
The developer of bootsplash appears to have lost interest in his project, given
some design problems. However, Gentoo developer <e>Michal Januszewski</e> is
developing a successor, <c>gensplash</c>, which in included in the
gentoo-sources-2.6 kernel. You can follow Michal's
<uri link="http://dev.gentoo.org/~spock/projects/gensplash/archive/gensplash-in-5-easy-steps.txt">
Gensplash in 5 easy steps</uri> document in order to familiarize yourself with
how gensplash is operated.
</p>

</body>
</section>
<section>
<title>I2C drivers now included in the kernel</title>
<body>

<p>
If you use <c>lm-sensors</c> to monitor system temperatures and power levels,
you previously needed to install the <c>i2c</c> package in order to provide
hardware support.
</p>

<p>
The I2C hardware drivers are now included in the Linux 2.6 kernel, no external
i2c package is required. Remember to compile support for your specific I2C
devices into the kernel configuration. You will then be able to use
<c>lm-sensors</c> as usual.
</p>

</body>
</section>


</chapter>

<chapter id="conf">
<title>Configuring, building, and installing the kernel</title>
<section>
<body>

<p>
As with Linux 2.4, you have two options for managing your new kernel build.
</p>

<ol>
  <li>
    The default method is to configure your kernel manually. This may seem
    daunting but is the preferred way as long as you know your system. If you
    wish to configure your new kernel manually, please continue on to the <uri
    link="#manual">next chapter</uri>.
  </li>
  <li>
    The alternative option is to use our <c>genkernel</c> utility to
    automatically configure, compile, and install a kernel for you. If you wish
    to use <c>genkernel</c> then skip over the next chapter and proceed with
    <uri link="#genkernel">using genkernel</uri>.
  </li>
</ol>

</body>
</section>
</chapter>

<chapter id="manual">
<title>Default: Manual configuration</title>
<section>
<title>Configuring the kernel</title>
<body>

<p>
We'll now get on with configuring the kernel. Open menuconfig in the usual way:
</p>

<pre caption="Invoking menuconfig">
# <i>cd /usr/src/linux</i>
# <i>make menuconfig</i>
</pre>

<p>
You will probably be familiar with using menuconfig from configuring 2.4
kernels. Fortunately, the front end has barely changed at all, but you will
observe much better organisation of kernel options, plus <e>many</e> new
options that weren't present in 2.4.
</p>

<p>
Be sure to enable the following important kernel options:
</p>

<pre caption="Required kernel options">
File systems ---&gt;
  Pseudo Filesystems ---&gt;
    [*] /proc file system support
    [*] Virtual memory file system support (former shm fs)
    
<comment>(the following are required for udev):</comment>
General setup  ---&gt;
 [*] Support for hot-pluggable devices

Device Drivers  ---&gt;
 Block devices  ---&gt;
  &lt;*&gt; RAM disk support
  
<comment>(the following are required for ALSA):</comment>
Device Drivers  ---&gt;
 Sound  ---&gt;
  &lt;*&gt; Sound card support
  Advanced Linux Sound Architecture  ---&gt;
   &lt;M&gt; Advanced Linux Sound Architecture
   &lt;M&gt; Sequencer support
   &lt;M&gt; OSS Mixer API
   [*] OSS Sequencer API
<comment>   (and dont forget to select your soundcard from the submenus!)</comment>

<comment>(the following are required if you use LVM for disk management):</comment>
Device Drivers  ---&gt;
 Multi-device support (RAID and LVM)  ---&gt;
  [*] Multiple devices driver support (RAID and LVM)
   &lt;*&gt;   Device mapper support
</pre>

<warn>
Previously you may have included support for the <path>/dev</path> file system
(now marked OBSOLETE). Do not enable devfs support. We have installed udev,
which we will be using instead of devfs from now on.
</warn>

<p>
Also, remember to enable support for the filesystems that you use, and the
hardware present in your system. Be sure to enable support for the IDE
controller on your motherboard if you wish to benefit from fast DMA disk
access. Refer to the <uri
link="/doc/en/handbook/handbook-x86.xml?part=1&amp;chap=7">Configuring the
Kernel</uri> section of the <uri link="/doc/en/handbook/index.xml">Gentoo
Handbook</uri> for additional guidance here. 
</p>

</body>
</section>
<section>
<title>Building the kernel</title>
<body>

<p>
Now that we have configured the kernel, we can start the compilation process:
</p>

<pre caption="Compiling the kernel source">
# <i>make &amp;&amp; make modules_install</i>
</pre>

<note>
You may recall having to run <c>make dep</c> with Linux 2.4 sources. This is no
longer required.
</note>

<p>
Wait for the kernel compilation to complete (and observe the much more readable
compilation output).
</p>

</body>
</section>
<section>
<title>Installing the kernel</title>
<body>

<p>
The next step is mounting your <path>/boot</path> partition and copying the
kernel image over. You must then update your bootloader config manually.
</p>

<pre caption="Installing the kernel">
# <i>mount /boot</i>
# <i>cp arch/i386/boot/bzImage /boot/bzImage-2.6.10-gentoo-r4</i>
# <i>cp System.map /boot/System.map-2.6.10-gentoo-r4</i>
</pre>

<p>
Note that the above instructions are examples only, you should follow your
usual procedure of updating kernels by following the instructions in the <uri
link="/doc/en/handbook/index.xml">Gentoo Handbook</uri> (see the <uri
link="/doc/en/handbook/handbook-x86.xml?part=1&amp;chap=7">Configuring the
Kernel</uri> chapter).
</p>

<p>
When updating your bootloader config, do not remove the old entry pointing at
your 2.4 kernel. This way, you will easily be able to switch between the two if
something is not working.
</p>

<p>
Now continue onto the <uri link="#modules">Module Configuration</uri> section.
</p>

</body>
</section>
</chapter>

<chapter id="genkernel">
<title>Alternative: Using genkernel</title>
<section>
<body>

<p>
If you prefer to use genkernel instead of manually configuring your kernel, you
will be happy to hear that using genkernel to produce 2.6 kernels is very
similar to the process you performed when producing your previous 2.4 kernel.
</p>

<p>
You should invoke genkernel as shown below:
</p>

<pre caption="Invoking genkernel with some common arguments">
# <i>genkernel --udev --menuconfig --bootloader=grub all</i>
</pre>

<p>
In the above example, we also take advantage of genkernel features to open
menuconfig to allow you to customise the kernel configuration (if you wish),
and to update the grub bootloader configuration after compilation. 
</p>

<p>
You should choose genkernel arguments that suit you, but do not forget to
include the <c>--udev</c> argument! Refer to the <uri
link="/doc/en/genkernel.xml">Gentoo Linux Genkernel Guide</uri> and the <uri
link="/doc/en/handbook/handbook-x86.xml?part=1&amp;chap=7">Configuring the
Kernel</uri> chapter of the <uri link="/doc/en/handbook/index.xml">Gentoo
Handbook</uri> for additional information.
</p>

<p>
If you choose to update your bootloader config yourself, then you must
remember to include the <c>udev</c> kernel parameter. A sample <e>grub</e>
config section is shown below, but remember to adjust the <e>real_root</e>
parameter for your system.
</p>

<pre caption="Sample GRUB config for genkernel + udev">
title=Gentoo Linux (2.6 kernel)
root (hd0,0)
kernel /kernel-2.6.10-gentoo-r4 <i>udev</i> root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3
initrd /initrd-2.6.10-gentoo-r4
</pre>

</body>
</section>
</chapter>

<chapter id="modules">
<title>Module Configuration</title>

<section>
<title>Installing external modules</title>
<body>

<p>
Many users will additionally rely on kernel modules that are built outside of
the kernel tree. Common examples are the binary ATI and Nvidia graphics
drivers. You now need to install those modules, which will compile against the
2.6 sources found at <path>/usr/src/linux</path>. This is the usual case of
<c>emerge packagename</c> for all the external modules you are used to using
with 2.4.
</p>

<p>
Refer again to the <uri
link="/doc/en/handbook/handbook-x86.xml?part=1&amp;chap=7">Configuring the
Kernel</uri> chapter of the <uri link="/doc/en/handbook/index.xml">Gentoo
Handbook</uri> for more info.
</p>

</body>
</section>
<section>
<title>Autoloading modules</title>
<body>

<p>
You may have decided to compile some kernel components as modules (as opposed
to compiled directly into the kernel) and would like to have them autoloaded on
bootup like you did with 2.4. Also, if you installed any external modules from
the portage tree (as described above) you will probably want to autoload them
too.
</p>

<p>
You can achieve this similarly as to how you did with 2.4. Simply open up the
file <path>/etc/modules.autoload.d/kernel-2.6</path> in a text editor and list
the names of the modules you would like autoloaded.
</p>

<pre caption="Opening the module autoload list in nano">
# <i>nano -w /etc/modules.autoload.d/kernel-2.6</i>
</pre>

<pre caption="Sample autoload list to load the 3c59x and nvidia modules">
# /etc/modules.autoload.d/kernel-2.6:  kernel modules to load when system boots.
#
# Note that this file is for 2.6 kernels.
#
# Add the names of modules that you'd like to load when the system
# starts into this file, one per line.  Comments begin with # and
# are ignored.  Read man modules.autoload for additional details.

3c59x
nvidia
</pre>

</body>
</section>
</chapter>

<chapter>
<title>LVM to LVM2 migration</title>
<section>
<title>Upgrading to LVM2 tools</title>
<body>

<note>
If you do not use LVM to manage your disk storage, you can safely skip
this chapter and skip onto the next.
</note>

<p>
Fortunately, upgrading from the LVM1 user tools to the LVM2 versions is very
simple:
</p>

<pre caption="Upgrading user-tools from LVM1 to LVM2">
# <i>emerge --unmerge lvm-user</i>
# <i>emerge lvm2</i>
</pre>

<note>
The LVM2 tools are fully backwards-compatible with LVM1. Your disk data will
not be touched. You are not breaking any backwards-compatibility by doing
this, you will continue to be able to boot 2.4 as usual.
</note>

</body>
</section>
</chapter>

<chapter>
<title>Booting into Linux 2.6</title>
<section>
<body>

<p>
It's now time to boot into Linux 2.6. Close all applications and reboot:
</p>

<pre caption="Rebooting">
# <i>umount /boot</i>
# <i>reboot</i>
</pre>

<p>
When you reboot, if you followed this document correctly so far, you will have
the option of either loading Linux 2.4 or Linux 2.6 from your bootloader.
Choose Linux 2.6.
</p>

<p>
Once the system has booted, check that things are working. If you made a
mistake in the kernel configuration, don't worry, you can skip back to the
<uri link="#conf">Configuring, building, and installing the kernel</uri>
section, make your change, recompile and install new kernel image, reboot, and
try again!
</p>

</body>
</section>
<section>
<title>Configuring and unmuting ALSA</title>
<body>

<p>
We will now complete the ALSA configuration and unmute the audio channels. The
ALSA packages provide a useful utility to make this process relatively simple:
</p>

<pre caption="Invoking the automatic ALSA configuration utility">
# <i>alsaconf</i>
</pre>

<p>
The process is straightforward: allow the <e>/etc/modules.d/alsa</e> file to
be automatically updated, and then allow ALSA to be reloaded. alsaconf will
then terminate, however you will need to run it multiple times if you have
multiple sound devices installed in your system.
</p>

<p>
You should now add <c>alsasound</c> to your boot runlevel, so that volumes
will be saved on shutdown and restored on bootup:
</p>

<pre caption="Adding alsasound to the boot runlevel">
# <i>rc-update add alsasound boot</i>
</pre>

<note>
The <c>alsaconf</c> utility chooses initial volume levels for your sound
devices. If these are inappropriate, you can modify them at any time with the
<c>alsamixer</c> utility.
</note>

</body>
</section>
<section>
<title>Any immediate problems?</title>
<body>

<p>
At this stage you should refer back to the <uri link="#pitfalls">Known
pitfalls with Linux 2.6 migration</uri> section which may be helpful with any
issues you encounter immediately.
</p>

</body>
</section>
</chapter>

<chapter>
<title>Header files and NPTL</title>
<section>
<body>

<p>
By now you are running Linux 2.6 and hopefully have all issues ironed out.  You
should now update your Linux kernel header files and re-merge glibc so that
userspace applications can take advantage of new Linux 2.6 features.
</p>

<pre caption="Updating to linux-headers">
# <i>emerge -u linux-headers</i>
</pre>

<p>
After updating your headers package, you should generally re-merge glibc.
There is a new feature here that you may be interested in - NPTL. NPTL is a new
threading model present in Linux 2.6, which features much quicker thread create
and destroy times. This won't make much of a difference to most systems, but
you may wish to enable it during this migration process! To enable NPTL, edit
<path>/etc/make.conf</path>, adding <e>nptl</e> to your USE variable.
</p>

<warn>
If you choose to also enable the "nptlonly" flag, be aware that you will no
longer be able to boot a 2.4 kernel.
</warn>

<p>
Now re-merge glibc (you should do this even if you did not choose to enable
NPTL).
</p>

<pre caption="Reinstalling glibc against the new kernel headers">
# <i>emerge -a glibc</i>
</pre>

<p>
If you enabled NPTL, existing binaries will not use it until they are
recompiled. However, any binaries compiled from this point onwards <e>will</e>
use NPTL. You may wish to recompile all binaries now, e.g.:
</p>

<pre caption="Recompiling all packages on the system">
# <i>emerge -e world</i>
</pre>

<p>
Alternatively, you can just let your system "naturally" convert itself to NPTL
as you update to newer versions of packages when they are released.
</p>

</body>
</section>
</chapter>

<chapter>
<title>Closing remarks</title>
<section>
<title>Problems?</title>
<body>

<p>
With the incredible amount of work that went into Linux 2.6, it is sometimes
inevitable that things which used to work fine, no longer function as expected.
</p>

<p>
If you have any problems with your 2.6 kernel, and you can confirm that this
problem does not exist with Linux 2.4, then please open a bug with us on our
<uri link="http://bugs.gentoo.org">Bugzilla</uri>. We will investigate the
issue, and if we find that it is a problem in the mainline kernel, we may then
ask you to file a report at the central kernel bugzilla.
</p>

</body>
</section>
<section>
<title>Conclusion</title>
<body>

<p>
Hopefully you have just completed a smooth migration and you are enjoying the
benefits which Linux 2.6 brings over 2.4.
</p>

<p>
I would like to say a word of thanks to the many users who effectively
'tested' this document while it was in its early stages, and provided feedback
about how the migration process went. Sorry that I did not reply to all the
emails (there were a lot!), but I did read every one, and refined this
document where appropriate. Enjoy your 2.6-enhanced systems :)
</p>

</body>
</section>
<section>
<title>Removing Linux 2.4 from your system</title>
<body>

<p>
After you have been running 2.6 for a while, you may decide that you no longer
have any requirement to be able to use Linux 2.4. The steps you can take to
clean up your system are detailed below. <e>Only follow the procedure in this
section if you are sure that you don't want/need to use 2.4 again!</e>
</p>

<p>
The 2.4 kernel source code can be removed, using the emerge utility as usual.
For example, assuming you have 2.4 versions of vanilla-sources and
gentoo-sources installed, you could use the following command to remove them
while keeping the 2.6 versions intact:
</p>

<pre caption="Example: Removing Linux 2.4 sources">
# <i>emerge --unmerge =vanilla-sources-2.4.* =gentoo-sources-2.4.*</i>
</pre>

<p>
Portage will not completely clean out your 2.4 kernel source installations,
because some temporary files are created during compilation. It is safe to
remove these remnants with the following command:
</p>

<pre caption="Removing remaining temporary files">
# <i>rm -rf /usr/src/linux-2.4.*</i>
</pre>

<p>
You can additionally remove modules and information files relating to your
old 2.4 kernel installations, as these are no longer needed.
</p>

<pre caption="Removing previously-installed 2.4 modules">
# <i>rm -rf /lib/modules/2.4.*</i>
</pre>

<p>
The 2.4 kernel binaries you used to boot from can also be safely removed.
You should mount your <c>/boot</c> partition, and remove those images. You
should also update your bootloader configuration so that it no longer
references these deleted kernel images.
</p>

<p>
Some Linux 2.4 users will have previously installed the <c>alsa-driver</c>
package to benefit from the new audio capabilities included in Linux 2.6. If
you were one of these users, and you followed the advice given earlier in this
document about building ALSA with the 2.6 kernel sources (as opposed to using
the <c>alsa-driver</c> package), then you can safely remove this to prevent
future conflicts.
</p>

<p>
Additionally, <c>lm-sensors</c> users will have previously used the <c>i2c</c>
package to provide the hardware drivers. As already mentioned, I2C drivers are
now included in the kernel, so this package can also be removed in order to
prevent future conflicts.
</p>

<p>
The devfs management daemon, <c>devfsd</c>, can also safely be removed, now
that we are using <c>udev</c> for device management.
</p>

<pre caption="Removing alsa-driver, i2c, and devfsd">
# <i>emerge --unmerge alsa-driver i2c devfsd</i>
</pre>

<p>
If you are LVM2 user, you may wish to convert your data into the LVM2 data
format in order to benefit from the advantages which LVM2 provides.
However, this operation will prevent you from ever accessing your LVM data
from a 2.4 kernel. If you want to continue with the conversion (this is totally
optional!), then you should examine the <c>vgconvert</c> man page for
instructions on how to carry this out. An example is shown below, where
<c>main</c> is the volume group name.
</p>

<pre caption="Converting a LVM1 volume to LVM2 format">
# <i>vgconvert -M2 main</i>
</pre>

</body>
</section>
</chapter>
</guide>