/[gentoo]/xml/htdocs/doc/en/vdr-guide.xml
Gentoo

Diff of /xml/htdocs/doc/en/vdr-guide.xml

Parent Directory Parent Directory | Revision Log Revision Log | View Patch Patch

Revision 1.5 Revision 1.6
1<?xml version="1.0" encoding="UTF-8"?> 1<?xml version="1.0" encoding="UTF-8"?>
2<!-- $Header: /var/cvsroot/gentoo/xml/htdocs/doc/en/vdr-guide.xml,v 1.5 2007/01/03 00:58:38 nightmorph Exp $ --> 2<!-- $Header: /var/cvsroot/gentoo/xml/htdocs/doc/en/vdr-guide.xml,v 1.6 2007/01/03 15:04:27 nightmorph Exp $ -->
3<!DOCTYPE guide SYSTEM "/dtd/guide.dtd"> 3<!DOCTYPE guide SYSTEM "/dtd/guide.dtd">
4 4
5<guide link="/doc/en/vdr-guide.xml"> 5<guide link="/doc/en/vdr-guide.xml">
6<title>Gentoo Linux VDR Guide</title> 6<title>Gentoo Linux VDR Guide</title>
7 7
151<section id="kernel_output"> 151<section id="kernel_output">
152<title>Checking the kernel output</title> 152<title>Checking the kernel output</title>
153<body> 153<body>
154 154
155<p> 155<p>
156It's recommended to mark every driver as module, so that you can to add the 156It's recommended to mark every driver as module, so that you can add the
157required module dynamically, especially if you don't know the module name. If 157required module dynamically, especially if you don't know the module name. If
158you know the module name already, select the driver as a built-in driver. 158you already know the module name, select the driver as a built-in driver.
159Compile the kernel, install the modules and boot it. Check to see if your kernel 159Compile the kernel, install the modules and boot it. You can check if your
160has successfully detected your card by using <c>dmesg</c>. 160kernel has successfully detected your card by using <c>dmesg</c>.
161</p> 161</p>
162 162
163<pre caption="Checking kernel output"> 163<pre caption="Checking kernel output">
164# <i>dmesg | grep DVB</i> 164# <i>dmesg | grep DVB</i>
165<comment>(If you own a TerraTec Cinergy T2, your output might look like this:)</comment> 165<comment>(If you own a TerraTec Cinergy T2, your output might look like this:)</comment>
299<pre caption="Starting lircd"> 299<pre caption="Starting lircd">
300# <i>/etc/init.d/lircd start</i> 300# <i>/etc/init.d/lircd start</i>
301</pre> 301</pre>
302 302
303<p> 303<p>
304Now it should be possible to watch <c>lircd</c> running and decoding key-presses. 304Now it should be possible to watch <c>lircd</c> capturing and decoding key
305Just run the command <c>irw</c>. Stop it with pressing Ctrl+C when you have 305presses. Just run the command <c>irw</c>. Stop it by pressing Ctrl+C when you
306enough. 306have enough.
307</p> 307</p>
308 308
309<pre caption="Testing LIRC"> 309<pre caption="Testing LIRC">
310# <i>irw</i> 310# <i>irw</i>
3110000000000001aa2 00 Exit Technisat_TTS35AI.conf 3110000000000001aa2 00 Exit Technisat_TTS35AI.conf
372# <i>emerge vdr-dxr3</i> 372# <i>emerge vdr-dxr3</i>
373# <i>echo em8300 &gt;&gt; /etc/modules.autoload.d/kernel-2.6</i> 373# <i>echo em8300 &gt;&gt; /etc/modules.autoload.d/kernel-2.6</i>
374</pre> 374</pre>
375 375
376<p> 376<p>
377em8300-modules needs some configuration that depends on the exact used 377The em8300 module need some configuration that depends on the exact revision of
378revision of the card. 378that card.
379</p> 379</p>
380 380
381<!-- 381<!--
382<p> 382<p>
383Because we (the authors) don't own a card that uses the dxr3config, we decided 383Because we (the authors) don't own a card that uses the dxr3config, we decided
491#204.152.189.113 <comment>(a specific host)</comment> 491#204.152.189.113 <comment>(a specific host)</comment>
492#0.0.0.0/0 <comment>(any host on any net - USE THIS WITH CARE!)</comment> 492#0.0.0.0/0 <comment>(any host on any net - USE THIS WITH CARE!)</comment>
493</pre> 493</pre>
494 494
495<p> 495<p>
496If you only want to use <c>vdr-xineliboutput</c> to view the picture 496If you only want to use <c>vdr-xineliboutput</c> to view the picture on the same
497on the same PC running VDR you can now 497computer as the one running VDR you can continue with <uri
498<uri link="#channel_list">continue with configuring your channel-list</uri>. 498link="#channel_list">configuring your channel list</uri>.
499</p> 499</p>
500 500
501<p> 501<p>
502Otherwise, you now simply <c>emerge media-plugins/vdr-xineliboutput</c> on your 502Otherwise, you now simply <c>emerge media-plugins/vdr-xineliboutput</c> on your
503client: 503client:
530<title>Creating a Channel List</title> 530<title>Creating a Channel List</title>
531<section> 531<section>
532<body> 532<body>
533 533
534<p> 534<p>
535To make VDR really useful you need to create an appropriate channel list. 535To make VDR really useful you need to create an appropriate channel list. There
536</p>
537
538<p>
539There is more than one way to get a working list of channels (besides 536is more than one way to get a working list of channels (besides downloading
540downloading one). The channel list installed by default is for DVB-S reception 537one). The channel list installed by default is for DVB-S reception on Astra on
541on Astra on 19.2°E. 53819.2°E.
542</p> 539</p>
543 540
544</body> 541</body>
545</section> 542</section>
546<section> 543<section>

Legend:
Removed from v.1.5  
changed lines
  Added in v.1.6

  ViewVC Help
Powered by ViewVC 1.1.20