1 | <?xml version='1.0' encoding='UTF-8'?> |
1 | <?xml version='1.0' encoding='UTF-8'?> |
2 | <!DOCTYPE sections SYSTEM "/dtd/book.dtd"> |
2 | <!DOCTYPE sections SYSTEM "/dtd/book.dtd"> |
3 | |
3 | |
4 | <!-- The content of this document is licensed under the CC-BY-SA license --> |
4 | <!-- The content of this document is licensed under the CC-BY-SA license --> |
5 | <!-- See http://creativecommons.org/licenses/by-sa/1.0 --> |
5 | <!-- See http://creativecommons.org/licenses/by-sa/1.0 --> |
6 | |
6 | |
7 | <!-- $Header: /var/cvsroot/gentoo/xml/htdocs/doc/en/handbook/hb-install-sparc-medium.xml,v 1.4 2004/04/15 11:59:45 swift Exp $ --> |
7 | <!-- $Header: /var/cvsroot/gentoo/xml/htdocs/doc/en/handbook/hb-install-sparc-medium.xml,v 1.5 2004/04/19 08:47:38 bennyc Exp $ --> |
8 | |
8 | |
9 | <sections> |
9 | <sections> |
10 | <section> |
10 | <section> |
11 | <title>Hardware Requirements</title> |
11 | <title>Hardware Requirements</title> |
12 | <subsection> |
12 | <subsection> |
13 | <title>Introduction</title> |
13 | <title>Introduction</title> |
14 | <body> |
14 | <body> |
15 | |
15 | |
16 | <p> |
16 | <p> |
17 | Before we start, we first list what hardware requirements you need to |
17 | Before we start, we first list what hardware requirements you need to |
18 | successfully install Gentoo on your box. This of course depends on your |
18 | successfully install Gentoo on your box. This of course depends on your |
19 | architecture. |
19 | architecture. |
20 | </p> |
20 | </p> |
21 | |
21 | |
22 | </body> |
22 | </body> |
… | |
… | |
391 | <ul> |
391 | <ul> |
392 | <li>Type of image: <c>Data Mode 1</c></li> |
392 | <li>Type of image: <c>Data Mode 1</c></li> |
393 | <li>Block size: <c>2048 bytes</c></li> |
393 | <li>Block size: <c>2048 bytes</c></li> |
394 | <li>File precursor and length of the image trailer: <c>0 bytes</c></li> |
394 | <li>File precursor and length of the image trailer: <c>0 bytes</c></li> |
395 | <li>Scrambled: <c>no</c></li> |
395 | <li>Scrambled: <c>no</c></li> |
396 | <li>Swapped: <c>no</c></li> |
396 | <li>Swapped: <c>no</c></li> |
397 | </ul> |
397 | </ul> |
398 | Now click on <c>OK</c> and then <c>Burn</c> (the CD-R) |
398 | Now click on <c>OK</c> and then <c>Burn</c> (the CD-R) |
399 | </li> |
399 | </li> |
400 | <li> |
400 | <li> |
401 | With cdrecord, you simply type <c>cdrecord dev=/dev/hdc</c> (replace |
401 | With cdrecord, you simply type <c>cdrecord dev=/dev/hdc</c> (replace |
402 | <path>/dev/hdc</path> with your CD-RW drive's device path) followed |
402 | <path>/dev/hdc</path> with your CD-RW drive's device path) followed |
403 | by the path to the ISO file :) |
403 | by the path to the ISO file :) |
404 | </li> |
404 | </li> |
405 | <li> |
405 | <li> |
406 | With K3B, select <c>Tools</c> > <c>CD</c> > <c>Burn Image</c>. The |
406 | With K3B, select <c>Tools</c> > <c>CD</c> > <c>Burn Image</c>. Then |
407 | under the 'Image to Burn' area, locate the ISO file. Finally click |
407 | you can locate your ISO file within the 'Image to Burn' area. Finally click |
408 | <c>Start</c>. |
408 | <c>Start</c>. |
409 | </li> |
409 | </li> |
410 | </ul> |
410 | </ul> |
411 | |
411 | |
412 | </body> |
412 | </body> |
413 | </subsection> |
413 | </subsection> |
414 | <subsection> |
414 | <subsection> |
415 | <title>Booting the SPARC LiveCD</title> |
415 | <title>Booting the SPARC LiveCD</title> |
416 | <body> |
416 | <body> |
417 | |
417 | |
418 | <p> |
418 | <p> |
419 | Insert the Gentoo LiveCD in the CD-ROM and boot your system. During startup, |
419 | Insert the Gentoo LiveCD in the CD-ROM and boot your system. During startup, |
420 | press Stop-A to enter OpenBootPROM (OBP). Once you are in the OBP, boot from the |
420 | press Stop-A to enter OpenBootPROM (OBP). Once you are in the OBP, boot from the |
421 | CD-ROM: |
421 | CD-ROM: |
422 | </p> |
422 | </p> |